TEXT

International Journal of Automotive and Mechanical Engineering (IJAME), VOLUME 2 , Juli - December 2015

---

-Direct injection of water mist in an intake manifold spark ignition engine, A.R. Babu, G. Amba Prasad Rao and T. Hari Prasad, 2809
- Sound intensity mapping of an engine dynamometer, M.S.M. Sani, M.M. Rahman, M.Z.Baharom and I. Zaman, 2820 .
-Effect of ZnO nano materials on grinding surface finishing, M. Yogeswaran, K. Kadirgama, M.M. Rahman, R. Devarajan and M.M. Noor, 2829
-Morphology and tensile properties of thermoplastic polyurethane-halloysite nanotube nanocomposites, Tayser Sumer Gaaz, Abu Bakar Sulong, Majid Niaz Akhtar and Muhammad Rafi Raza, 2844
-Experimental study of heat transfer enhancement in automobile radiator using Al2O3/water–ethylene glycol nanofluid coolants, K.P. Vasudevan Nambeesan, R. Parthiban, K. Ram Kumar, U.R. Athul, M. Vivek and S. Thirumalini
-Comparative study of diesel engine performance and emission with soybean and waste oil biodiesel fuels, A.K. Azad, M.G. Rasul, Brady Giannangelo and Rubayat Islam, 2866
-Mechanical properties of bamboo reinforced epoxy sandwich structure composites, S.A.H. Roslan, M.Z. Hassan, Z.A. Rasid, S.A. Zaki, Y. Daud, S. Aziz, S. Sarip and Z. Ismail, 2882
-Integration of vehicle dynamics control systems with an extendable bumper for collision mitigation, M. Elkady, A. Elmarakbi and J. MacIntyre, 2893
-Integration of vehicle dynamics control systems with an extendable bumper for collision mitigation, M. Elkady, A. Elmarakbi and J. MacIntyre, 2893
-Effects of isentropic efficiencies on the performance of combined cycle power plants,Thamir K. Ibrahim and M. M. Rahman, 2914
-Effects of flow parameters on the performance of vertical axis swirling type Savonius wind turbine, A. Al-Faruk and A. S. Sharifian, 2929
-Characteristics of solar energy radiation on typical summer and winter days in Kuwait, M.A. Bou-Rabee, S.A. Sulaiman, G. Choe, D. Han, T. Saeed and S. Marafie, 2944
-Effects of accelerators on the cure characteristics and mechanical properties of natural rubber compounds, Q. Ahsan, N. Mohamad and T.C. Soh, 2954
-Performance and emission comparison of Karanja (pongamia pinnata), Pithraj (aphanamixis polystachya), Neem (azadira chtaindica) and Mahua (madhuca longofolia) seed oil as a potential feedstock for biodiesel production in Bangladesh,N. Hoque, M. Mourshed and B. K. Das, 2967
-Energy audit and waste heat recovery system design for a cement rotary kiln in Ethiopia: A case study, T.T. Ayu, M.H. Hailu, F.Y. Hagos and S.M. Atnaw, 2983
-Multi-objective optimization of minimum quantity lubrication in end milling of aluminum alloy AA6061T6, M.S. Najiha, M.M. Rahman, K. Kadirgama, M.M. Noor and D. Ramasamy,3003
-Analytical-experimental analysis of last generation medium-size motorcycles emission behaviour under real urban conditions,Paolo Iodice and Adolfo Senatore, 3018
-Mechanical properties and microstructure of precipitation-hardened Al-Cu-Zn alloys,J.K. Odusote, A.A. Adeleke and P.A. Ajayi, 3033
-Experimental study of split air conditioner with and without trombone coil condenser as air conditioning water heater, Azridjal Aziz, Arya Bhima Satria and Rahmat Iman Mainil, 3043
-
Optimum preparation and thermal conductivity of novel glossy paint prepared from waste of palm oil fly ash composite
C.K. Sia, W. L. Tan, O.L.C. Narong, S. Hakimi Mohd Nor, S. K. Yee and P. Ong, 3058
-Effect of tube spacing, fin density and Reynolds number on overall heat transfer rate for in-line configuration
Tahseen A. Tahseen, M.M. Rahman and M. Ishak, 3065
-Investigation of accident scenarios between pedestrians and city buses in Thailand
S. Lakkam and S. Koetniyom, 3076
-
Influence of powder morphology and sintering temperature on the properties of hydroxyapatite
W.J. Kelvin Chew, A. Niakan, N.A. Nawawi, L.T. Bang and S. Ramesh, 3089
-Effect of nano-particles on the performance and emission of a diesel engine using biodiesel-diesel blend
M. Ghafoori, B. Ghobadian, G. Najafi, M. Layeghi, A. Rashidi and R. Mamat, 3097
-Comparison of numerical simulation and experimental study on indoor air quality of air-conditioned office building in desert climate
A.M. Wahhad, N. M. Adam and S.M. Sapuan, 3109
-
Simulation of ignition delay time of compressed natural gas combustion
Yuswan Muharam, Mirza Mahendra, Dinda Gayatri and Sutrasno Kartohardjono, 3125

---

Ketersediaan

Informasi Detail

Judul Seri

International Journal of Automotive and Mechanical Engineering (IJAME)

No. Panggil

REF 620 TIM i

Penerbit

Malaysia : Universiti Malaysia Pahang., 2015

Deskripsi Fisik

2809-3140

Bahasa

Indonesia

ISBN/ISSN

2229--8649

Klasifikasi

620

Tipe Isi

-

Tipe Media

-

Tipe Pembawa

-

Edisi

VOLUME 2 , Juli - December 2015

Subjek

Configuration
natural gas combustion
Simulation of ignition delay
Comparison of numerical simulation
experimental study on indoor air quality of air-co
Effect of nano-particles on the performance
emission of a diesel engine using biodiesel-diesel
Influence of powder morphology
sintering temperature on the properties
Investigation of accident scenarios
between pedestrians and city buses in Thailand
Effect of tube spacing
Optimum preparation
fly ash composite
Experimental study
Mechanical properties
Analytical-experimental analysis
generation medium-size motorcycles
Multi-objective optimization of minimum
Energy audit and waste heat recovery
Performance and emission comparison of Karanja
pongamia pinnata
Effects of accelerators on the cure characteristic
mechanical properties of natural rubber compounds
Characteristics of solar energy radiation
Effects of flow parameters
performance of vertical axis swirling
Effects of isentropic efficiencies
performance of combined cycle power plants
Integration of vehicle dynamics
Comparative study of diesel engine
performance and emission with soybean
Experimental study of heat transfer
Morphology and tensile properties
Effect of ZnO nano materials
Sound intensity mapping of an engine dynamometer
Direct injection of water mist

Info Detail Spesifik

-

Pernyataan Tanggungjawab

International Journal of Automotive and Mechanical Engineering (IJAME)

Versi lain/terkait

Lampiran Berkas

Komentar

---

Anda harus masuk sebelum memberikan komentar